1. VACUUM BAGGING FILMS
A flexible, extruded film is normally used to form the vacuum bag and this is supplied either in tubular or sheet form.The film is sealed to the edge of the mould with vacuum bag sealant tape. Click here to download the vacuum bagging films catalogue and technical data sheets.

2. SEALANT TAPES
Sealant tapes are used to provide a vacuum-tight seal between the bag and the mould. The tape must have sufficient tack to adhere well to the mould surface but not too much that the bag cannot be stripped away from the tape to allow re-positioning.The tape must also strip cleanly from the mould surface after the cure cycle. An extensive range of tapes covering all cure conditions is available.
Click here to download the sealant tapes catalogue and technical data sheets.

3. BLEEDER & BREATHER FABRICS
Non-woven bleeder/breather fabrics allow air and volatiles to be removed from within the vacuum bag throughout the cure cycle.They are also used to absorb excess resin present in some composite lay ups.Various products are available and selection depends on the temperature/pressures they must withstand during the cure.
Click here to download the bleeder and breather fabrics catalogue and technical data sheets.

4. RELEASE FILMS
Release films are typically placed directly in contact with the laminate.They separate the laminate from the breather fabric, which has no release characteristics. Many types of release films exist and selection depends on cure temperature, pressure, complexity of component and resin system involved. Release films are often perforated to ensure that any trapped air or volatiles, which may compromise the laminate, are removed.Various perforation types are available.
Click here to download the release films catalogue and technical data sheets.

5. RELEASE FABRICS/PEEL PLIES
Both release fabrics and peel plies are placed against the surface of the laminate. They are woven products which are strong and have good heat resistance. Release films impart a gloss finish on the cured laminate whereas peel plies and release fabrics leave an impression of the weave pattern. Peel plies provide a clean, uncontaminated surface for subsequent bonding or painting.
Click here to download the peel plies catalogue and technical data sheets.

6. ADHESIVE TAPES
Adhesive tapes have many functions.They remove resin flash from the edge of the laminate, hold the consumable package in place and tape down the pleats of the vacuum bag.Various carrier films/adhesive systems exist and can be found in this section.
Click here to download the adhesive tapes catalogue and technical data sheets.

7. PTFE COATED GLASS
These materials are designed for use with flat or single curvature tooling and when applied to the tool surface, eliminate the need for application of release agents.
Click here to download the PTFE coated glass catalogue and technical data sheets.

9. RUBBER PRODUCTS
Aerovac offers a full range of cured and uncured rubber products in sheet and roll form.
Click here to download the rubber products catalogue and technical data sheets.

8. VACUUM FITTINGS
A selection of vacuum fittings including vacuum breach units, non-return, plug and socket couplings and vacuum/autoclave hoses are found in this section. Reliability of these items is paramount in ensuring that leaks do not occur.
Click here to download the vacuum vacuum fittings catalogue and technical data sheets.

10. MISCELLANEOUS ITEMS
Ancillary products for the composite workshop.
Click here to download the miscellaneous items catalogue and technical data sheets.

11. KITTING AND LAMINATION
Aerovac offers a service for the management of consumables used in the manufacture of composite work pieces:Consumables which are cut, assembled and treated to measure. Aerovac proposes some customised multi-layers products.
Click here to download the kitting and lamination catalogue and technical data sheets.

12. INFUSION RANGE
Aerovac, thanks to its research and development activities, has become a specialist in the infusion lamination process by developing its own range of reusable products and tools which are specifically adapted to this process.
Click here to download the infusion catalogue and technical data sheets.

13. TOOLINGS
A manufacturer of composites moulds and reusable systems for vacuum composites processes, Aerovac systèmes France is a firm believer in visiting and providing consultancy to its clients. From 3D modelling to seating ergonomics, a team of engineers is ready to help with your design and implementation requirements. A mobile technical team can also work with you on your facility when the dimensions of the tooling to be implemented require this.
Click here to download the toolings catalogue and technical data sheets.


Click here to download the complete catalogue of aerovac products, toolings and services.
Many other products are also available. Do not hesitate to let us know your needs. Our sales team is ready to help you with any information and technical support you may need in your projects.